网工必备技术
防火墙双机热备技术
双机热备技术原理：
产生原因：传统的组网方式，内部用户和外部用户的交互报文全部通过Firewall 。如果Firewall出现故障，内部网络中所有以Firewall作为默认网关的主机与外部网络之间的通讯将中断，通讯可靠性无法保证。
VRRP在防火墙应用中存在的缺陷：传统VRRP方式无法实现主、备用防火墙状态的一致性。
为了保证所有VRRP备份组切换的一致性，在VRRP的基础上进行了扩展，推出了VGMP（VRRP Group Management Protocol）来弥补此局限。
防火墙双机热备使用的技术：VGMP。
VGMP基本原理：
当防火墙上的VGMP为Active/Standby状态时，组内所有VRRP备份组的状态统一为Active/Standby状态。
状态为Active的VGMP也会定期向对端发送HELLO报文，通知Standby端本身的运行状态(包括优先级、VRRP成员状态等)。
解释：
定期VGMP HELLO报文发送周期缺省为1秒。
当Standby端三个HELLO报文周期没有收到对端发送的HELLO报文时，即3s。
会认为对端出现故障，从而将自己切换到Active状态。
HRP（Huawei Redundancy Protocol）协议==心跳线。
两台FW之间备份的数据是通过心跳口发送和接收的，是通过心跳链路（备份通道）传输的。
心跳口必须是状态独立且具有IP地址的接口，可以是一个物理接口（GE接口），也可以是为了增加带宽，由多个物理接口捆绑而成的一个逻辑接口Eth-Trunk。
双机热备基本组网：
VRRP配置过程：
1.地址配置（基础配置）。2.安全区域的划分。3.策略放行。4.VRRP组的创建。5.HRP的配置：
启用HRP备份功能。
启用允许配置备用设备的功能。
启用命令与状态信息的自动备份。
启用会话快速备份。
检查命令：display vrrp interface X/X/X。检查心跳线的状态：dis hrp state。
防火墙直路部署，上下行连接交换机
1.完成网络基本配置。
配置FW各接口的IP地址:
<FW_A> system-view [FW_A] interface GigabitEthernet 1/0/1 [FW_A-GigabitEthernet1/0/1] ip address 10.2.0.1 24 [FW_A-GigabitEthernet1/0/1] quit [FW_A] interface GigabitEthernet 0/0/3 [FW_A-GigabitEthernet1/0/3] ip address 10.3.0.1 24 [FW_A-GigabitEthernet1/0/3] quit [FW_A] interface GigabitEthernet 1/0/6 [FW_A-GigabitEthernet1/0/6] ip address 10.10.0.1 24
<FW_B> system-view [FW_B] interface GigabitEthernet 0/0/1 [FW_B-GigabitEthernet1/0/1] ip address 10.2.0.2 24 [FW_B-GigabitEthernet1/0/1] quit [FW_B] interface GigabitEthernet 0/0/3 [FW_B-GigabitEthernet1/0/3] ip address 10.3.0.2 24 [FW_B-GigabitEthernet1/0/3] quit [FW_B] interface GigabitEthernet 1/0/6 [FW_B-GigabitEthernet1/0/6] ip address 10.10.0.2 24
将FW各接口加入相应的安全区域:
[FW_A] firewall zone trust [FW_A-zone-trust] add interface GigabitEthernet 1/0/3 [FW_A-zone-trust] quit [FW_A] firewall zone dmz [FW_A-zone-dmz] add interface GigabitEthernet 1/0/6 [FW_A-zone-dmz] quit [FW_A] firewall zone untrust [FW_A-zone-untrust] add interface GigabitEthernet 1/0/1 [FW_A-zone-untrust] quit
[FW_B] firewall zone trust [FW_B-zone-trust] add interface GigabitEthernet 1/0/3 [FW_B-zone-trust] quit [FW_B] firewall zone dmz [FW_B-zone-dmz] add interface GigabitEthernet 1/0/6 [FW_B-zone-dmz] quit [FW_B] firewall zone untrust [FW_B-zone-untrust] add interface GigabitEthernet 1/0/1 [FW_B-zone-untrust] quit
配置VRRP备份组:
[FW_A] interface GigabitEthernet 1/0/1 [FW_A-GigabitEthernet0/0/1] vrrp vrid 1 virtual-ip 1.1.1.1 24 active [FW_A-GigabitEthernet0/0/1] quit
[FW_B] interface GigabitEthernet 1/0/1 [FW_B-GigabitEthernet0/0/1] vrrp vrid 1 virtual-ip 1.1.1.1 24 standby [FW_B-GigabitEthernet0/0/1] quit
[FW_A] interface GigabitEthernet 0/0/3 [FW_A-GigabitEthernet0/0/3] vrrp vrid 2 virtual-ip 10.3.0.3 active [FW_A-GigabitEthernet0/0/3] quit
[FW_B] interface GigabitEthernet 0/0/3 [FW_B-GigabitEthernet0/0/3] vrrp vrid 2 virtual-ip 10.3.0.3 standby [FW_B-GigabitEthernet0/0/3] quit
指定心跳口并启用双机热备功能:
[FW_A] hrp interface GigabitEthernet 1/0/6 remote 10.10.0.2 [FW_A] hrp enable
[FW_B] hrp interface GigabitEthernet 1/0/6 remote 10.10.0.1 [FW_B] hrp enable
配置安全策略，允许内网用户访问Internet:
HRP_M[FW_A] security-policy HRP_M[FW_A-policy-security] rule name trust_to_untrust HRP_M[FW_A-policy-security-rule-trust_to_untrust] source-zone trust HRP_M[FW_A-policy-security-rule-trust_to_untrust] destination-zone untrust HRP_M[FW_A-policy-security-rule-trust_to_untrust] source-address 10.3.0.0 24 HRP_M[FW_A-policy-security-rule-trust_to_untrust] action permit HRP_M[FW_A-policy-security-rule-trust_to_untrust] quit HRP_M[FW_A-policy-security] quit
在FW_A上配置NAT策略:
HRP_M[FW_A] nat address-group group1 HRP_M[FW_A-address-group-group1] section 0 1.1.1.2 1.1.1.5 HRP_M[FW_A-address-group-group1] route enable HRP_M[FW_A-address-group-group1] quit HRP_M[FW_A] nat-policy HRP_M[FW_A-policy-nat] rule name policy_nat1 HRP_M[FW_A-policy-nat-rule-policy_nat1] source-zone trust HRP_M[FW_A-policy-nat-rule-policy_nat1] destination-zone untrust HRP_M[FW_A-policy-nat-rule-policy_nat1] source-address 10.3.0.0 16 HRP_M[FW_A-policy-nat-rule-policy_nat1] action source-nat address-group group1
pc1:
PC2:
验证网络是否连通:
防火墙直路部署，上下行连接交换机的负载分担组网
完成基本配置:
<FW_A> system-view [FW_A] interface GigabitEthernet 1/0/1 [FW_A-GigabitEthernet1/0/1] ip address 10.2.0.1 24 [FW_A-GigabitEthernet1/0/1] quit [FW_A] interface GigabitEthernet 1/0/3 [FW_A-GigabitEthernet1/0/3] ip address 10.3.0.1 24 [FW_A-GigabitEthernet1/0/3] quit [FW_A] interface GigabitEthernet 1/0/7 [FW_A-GigabitEthernet1/0/7] ip address 10.10.0.1 24 [FW_A-GigabitEthernet1/0/7] quit
<FW_B> system-view [FW_B] interface GigabitEthernet 1/0/1 [FW_B-GigabitEthernet1/0/1] ip address 10.2.0.2 24 [FW_B-GigabitEthernet1/0/1] quit [FW_B] interface GigabitEthernet 1/0/2 [FW_B-GigabitEthernet1/0/2] ip address 10.3.0.2 24 [FW_B-GigabitEthernet1/0/2] quit [FW_B] interface GigabitEthernet 1/0/7 [FW_B-GigabitEthernet1/0/7] ip address 10.10.0.2 24 [FW_B-GigabitEthernet1/0/7] quit
将FW各接口加入相应的安全区域:
[FW_A] firewall zone untrust [FW_A-zone-untrust] add interface GigabitEthernet 0/0/1 [FW_A-zone-untrust] quit [FW_A] firewall zone trust [FW_A-zone-trust] add interface GigabitEthernet 1/0/3 [FW_A-zone-trust] quit [FW_A] firewall zone dmz [FW_A-zone-dmz] add interface GigabitEthernet 0/0/7 [FW_A-zone-dmz] quit
[FW_B] firewall zone untrust [FW_B-zone-untrust] add interface GigabitEthernet 0/0/1 [FW_B-zone-untrust] quit [FW_B] firewall zone trust [FW_B-zone-trust] add interface GigabitEthernet 0/0/3 [FW_B-zone-trust] quit [FW_B] firewall zone dmz [FW_B-zone-dmz] add interface GigabitEthernet 0/0/7 [FW_B-zone-dmz] quit
配置VRRP备份组:
[FW_A] interface GigabitEthernet 1/0/1 [FW_A-GigabitEthernet1/0/1] vrrp vrid 1 virtual-ip 1.1.1.3 24 active [FW_A-GigabitEthernet1/0/1] vrrp vrid 2 virtual-ip 1.1.1.4 24 standby [FW_A-GigabitEthernet1/0/1] quit
[FW_B] interface GigabitEthernet 1/0/1 [FW_B-GigabitEthernet1/0/1] vrrp vrid 1 virtual-ip 1.1.1.3 24 standby [FW_B-GigabitEthernet1/0/1] vrrp vrid 2 virtual-ip 1.1.1.4 24 active [FW_B-GigabitEthernet1/0/1] quit
[FW_A] interface GigabitEthernet 1/0/2 [FW_A-GigabitEthernet1/0/2] vrrp vrid 3 virtual-ip 10.3.0.3 active [FW_A-GigabitEthernet1/0/2] vrrp vrid 4 virtual-ip 10.3.0.4 standby [FW_A-GigabitEthernet1/0/2] quit
[FW_B] interface GigabitEthernet 1/0/2 [FW_B-GigabitEthernet1/0/2] vrrp vrid 3 virtual-ip 10.3.0.3 standby [FW_B-GigabitEthernet1/0/2] vrrp vrid 4 virtual-ip 10.3.0.4 active [FW_B-GigabitEthernet1/0/2] quit
配置会话快速备份功能，指定心跳口并启用双机热备功能:
[FW_A] hrp mirror session enable [FW_A] hrp interface GigabitEthernet 0/0/7 remote 10.10.0.2 [FW_A] hrp enable
[FW_B] hrp mirror session enable [FW_B] hrp interface GigabitEthernet 0/0/7 remote 10.10.0.1 [FW_B] hrp enable
配置安全策略:
HRP_M[FW_A] security-policy HRP_M[FW_A-policy-security] rule name trust_to_untrust HRP_M[FW_A-policy-security-rule-trust_to_untrust] source-zone trust HRP_M[FW_A-policy-security-rule-trust_to_untrust] destination-zone untrust HRP_M[FW_A-policy-security-rule-trust_to_untrust] action permit HRP_M[FW_A-policy-security-rule-trust_to_untrust] source-address 10.3.0.0 24 HRP_M[FW_A-policy-security-rule-trust_to_untrust] quit HRP_M[FW_A-policy-security] quit
配置NAT策略:
HRP_M[FW_A] nat address-group group1 HRP_M[FW_A-address-group-group1] section 0 1.1.2.5 1.1.2.8 HRP_M[FW_A-address-group-group1] route enable HRP_M[FW_A-address-group-group1] quit
HRP_M[FW_A] nat-policy HRP_M[FW_A-policy-nat] rule name policy_nat1 HRP_M[FW_A-policy-nat-rule-policy_nat1] source-zone trust HRP_M[FW_A-policy-nat-rule-policy_nat1] destination-zone untrust HRP_M[FW_A-policy-nat-rule-policy_nat1] source-address 10.3.0.0 24 HRP_M[FW_A-policy-nat-rule-policy_nat1] action source-nat address-group group1 HRP_M[FW_A-policy-nat-rule-policy_nat1] quit HRP_M[FW_A-policy-nat] quit
注意：对于双机热备的负载分担组网，为了防止两台设备进行NAT转换时端口冲突，需要在FW_A和FW_B上分别配置可用的端口范围。
在FW_A上进行如下配置：
HRP_M[FW_A] hrp nat resource primary-group
PC：
推荐阅读
>>>【独家首发】新版HCIE考试解读直播回顾
>>> 重磅！华为HCIE认证改版升级通知！
>>>【命令解析】Linux用户行为的常用命令
>>> 网工必备通信基础知识，还不知道你就out了？
>>>【必备干货】网工入门必会桥接教程，外网+GNS3+Vmware
>>>【技术指南】5分钟搞清楚OSPF链路状态路由协议
网工界市场认可度极高的华为认证，你考了吗？
拿下华为HCIE认证之后，你可以：
跨越90%企业的招聘硬门槛
增加70%就业机会
拿下BAT全国TOP100大厂敲门砖
体系化得到网络技术硬实力
技术大佬年薪可达30w+
